Single-Use Pressure Sensors
Equipped with PendoTECH High Accuracy Pressure (MEMS-HAP™) Chips, these sensors are ideal for various processes such as filtration, chromatography, gas and disposable bioreactor monitoring, filling operations, and more. They are made from caustic-resistant polysulfone to endure sanitization processes.
Rated for use up to 75 psi, these sensors are compatible with PendoTECH’s PressureMAT™ monitor/transmitter, PendoTECH’s Process Control Systems, or other pre-qualified third-party monitors. Experience the dependability of PendoTECH’s pressure sensors in your biopharmaceutical processes.
The pressure sensors can be integrated for pressure measurement and control with either a PressureMAT™ System (monitor/transmitter) or a PendoTECH Process Control System, depending on the number of sensors and process requirements. The data collected by these systems can be output to a PC or another data monitoring device. They also can be integrated into other pre-qualified 3rd party pumps & monitors. The pressure sensors are very accurate in the pressure ranges typically used with flexible tubing and are qualified for use to 75 psi.
Process Scale Pressure Sensors
- Applications include multi-stage depth filtration, TFF/crossflow filtration, and bioreactor pressure monitoring and many more
- Available for use with tubing from 1/8 inch to 1 inch inner diameter (for luer size see below) or a sanitary flange
- Unobstructed flow path & no dead legs provides dramatically reduced hold-up volume versus stainless steel transducers or gauges
- Qualified for use in the range from -7 to 75 psi
- Compatible with gamma irradiation
- All materials meet USP Class VI
- Integral 12 inch cable connects to reusable monitor/ transmitter/alarm cable via molded connector
- Each sensor is tested for quality and accuracy during manufacturing and rejected if out of specification (no calibration required)
- Manufactured in a clean room in an ISO 9001-certified facility
- Can be cleaned and re-used
- Cost-effective
- Autoclave Compatible
- Polycarbonate material or caustic resistant polysulfone (please review Application Note- Autoclave of Single Use Pressure Sensors)
- Certificate of quality included with lot certification; individual NIST Calibration Certificates are optional
- May be non-invasively tested in-place with the PressureCHECKER™ device
- Validation guide available upon request
Hose Barb Design Features
The design features no mold parting line where the tubing is secured, which can be a source of leaks. The single barb shaft allows the hose to relax behind the barb, causing the tie-wrap to work like a drawstring. A tie-wrap placed over the anti-rotation device will lock the tubing, preventing it from becoming loose by a twisting motion. If a more secure fitting than a tie-wrap is required for higher pressure, either a BarbLock or Oetiker Clamp can be used, and they both give a very secure 360° radial compression seal.
PendoTECH Pressure Sensors – for Smaller Scale Processes
The luer sensors are offered in polycarbonate and polysulfone and have male/female luer lock inlet/outlet ports and come with a cap on the female luer port for dead-end applications. With the universal luer fitting, they can be adapted to processes in different manners. A couple of examples are they can be used in-line at low flow rates (1/16 or 1/8 inch tubing) or on a 1/4 or 3/8 inch barb fitting with luer port. The polycarbonate version is sterile for aseptic connection.
PendoTECH Pressure Sensor Data* 100 Sensors
* Data from 100 random sensors manufactured with the PendoTECH High Accuracy Pressure chips (MEMS-HAP chips) and measured with the PendoTECH Process Control System.
BarbLock® is a registered trademark of Saint-Gobain Performance Plastics Corporation all rights reserved.
Adaptor Cables for Third Party Monitors
- PDKT-650-298SC – Reusable shielded 6 ft connector cable w/ phone jack for Scilog pumps
- PDKT-650-298MG – Reusable shielded 6 ft connector cable w/phone jack for Midgee monitor
- PDKT-650-298MN – Reusable shielded 6 ft connector cable w/ phone jack for Pall Minim
Fittings
- PDKT-103-03 – 1/4inch x 1/4inch polycarbonate straight connector with luer port
- PDKT-104-03 – 3/8inch x 3/8inch polycarbonate straight connector with luer port
- PDKT-105-03 – 1/2inch x 1/2inch polycarbonate straight connector with luer port
- PDKT-V3PS-000 – Luer polysulfone 3-way stopcock
- PDKT-650-298 – Reusable shielded connector 12 ft cable for sensor w/ colored leads
- PDKT-650-298BH – Bulkhead connector for panel mount connection of PendoTECH Pressure & Conductivity Sensors
- PMAT-EXT-12F – Pressure senor extension cable (12ft)
- PendoTECH PressureCHECKER™ for non-invasive testing of sensors
- PDKT-650-298CVR – Pressure sensor cable dust cover/zero simulator for PressureMAT
Data Sheets
- Single Use Pressure Sensor Data Sheet
- Single Use Pressure Sensors for Use in Flexible BioProcess Containers Data Sheet
- PendoTECH cable adaptor for Single Use Pressure Sensor – PDKT-650-298
- Panel mount connection of PendoTECH Pressure & Conductivity Sensors- PDKT-650-298BH
Technical Notes
- Application Note: Autoclave
- Application Note: Short Term NaOH Compatibility
- Technical Note: Sensor Materials
- Application Note: PendoTECH Single Use Pressure Sensors™: For Single Use and Glass Bioreactor Monitoring and Control
- PendoTECH Single Use Pressure Sensors with Ingress-Protection (IP) Rated 67 Connectors
- PendoTECH Single Use Pressure Sensors: Calibration, Accuracy, and Implementation
- PendoTECH Sensor Chemical Compatibility
- Application Note: Measuring the Liquid Volume in a BioProcess Container
- Technical Note: PendoTECH Sensors and Industry 4.0: Integrating a PendoTECH Single Use Sensor System with a Digital Highway
- Application Note: Preliminary X-Ray Irradiation Evaluation
Application Notes
Articles
- “Single-Use Pressure Sensors for Continuous Processing and Leak Testing” – Dennis Annarelli, PhD, Mark Marrano, Josh Huang, and Jim Furey- Genetic Engineering News, (Sept 2018)
- “Single-Use Noninvasive Sensing Technology” – Jim Furey – Genetic Engineering News, (July 2009)
- “Using In-Line Disposable Pressure Sensors to Evaluate Depth Filter Performance” – Lee R. Bink and Jim Furey – BioProcess International 8(2), (February 2010)
- “Measuring Pressure at Very Low Levels with High Accuracy in Single-Use Systems” – Dennis C. Annarelli, Jim Furey, Benjamin Less, and Joshua Huang – BioProcess International 13(3)s, (March 2015)